why portforwarding ?
portforwarding enables you to get better torrent speeds. although the torrent speed depends upon number of seeders and leechers, portforwarding plays a main role in getting high torrent speeds!. experience download speed at maximum speed after portforwarding your modem!!
for old firmware visit here.
how to portforward your bsnl/dataone ut300r2u modem?
you need:
- a torrent client like microtorrent (my favourite)
- a browser: firefox( again my favourite)
when you open the torrent client for the first time ,you will asked to test the ports to get optimum speeds(shown below)
most of the times the it wont be portforwarded and you would be directed to www.portforward.com. although most of the times the site helps you in port forwarding ,it didn’t work everytime for me.sometimes it would work and sometimes it wudn’t.there was no REALIABILITY . however it did help me partially.
the following method works everytime for me.
- start torrent client.(read Utorrent).
- then in the menu bar…OPTIONS>>PREFERENCES>> CONNECTION as shown below
- uncheck enable upnp port mapping as shown,note down the random port number it will be used later. click apply and then ok as shown. now close torrent client
ACCESSING THE ROUTER /MODEM PAGE:
- now open any browser.type 192.168.1.2 or 192.168.1.1 in the address bar to log into modem/router page as shown below
- enter the username as admin and password as admin and click ok as shown above.that should get you to routers page.
- once you are in the routers page click on advanced tab as shown below.
- click on the virtual server button as shown below
- fill the details in the page.let PRIVATE IP = 192.168.1.136, PROTOCOL=ANY, LOCAL PORT=port number you noted down earlier, select single port from drop down and click apply as shown below.you will see that virtual server list is updated.
- now close the browser
- now click START>>MY NETWORK PLACES>>VIEW NETWORK CONNECTIONS
- right click on your LOCAL AREA CONNECTION>>PROPERTIES
- click on INTERNET PROTOCOL(TCP/IP)>>PROPERTIES as shown in the figure
- click on use the following IP address and enter the details as shown above.
- i am using open dns server address.you can also use bsnl dns server address but they are more subject to downtime compared to open dns server address. and this guide is not tested on bsnl dns server addresses.
- click ok to close both the windows.
here lies the catch……….
the above instructions are also given in the portforward.com. now open the browser and start surfing. if you can browse the internet pages its well and good. portforwarding is done successfully.
if you cannot browse the internet,don’t worry just restart the system.now you should be able to browse the internet .start the torrent client now.
you should be seeing a image similar to below image.
if you see the yellow triangle the port is not forwarded yet.go back to ACCESSING ROUTER/MODEM PAGE step above and redo the changes till you create a virtual server.no need to make changes in local area connection.you need not restart this time.
just start the torrent again. click on the place where you see the yellow triangle,the speed guide window should pop up.select TEST IF PORT FORWARDED PROPERLY button as shown below.
- now the browser opens automatically ,and you should see the following page
now the port has been forwarded properly.
Note:
- you may have to create virtual server every time you start your system. but its better than having low speed downloads.
- i have connected to internet using usb port.and this guide is not tested on ethernet port ,i tried using ethernet,it works fine.the only thing you need to change is default gateway which is 192.168.1.1.please try the above method once,tell me if anything goes wrong.
- visit portforward.com for more detail.:
worst case solution:
if this guide doesn’t work for you and you badly need high torrent speeds,then in the advanced tab of router page ,you have dmz (demilitarised zone) button. click on the button. you will be required to enter the the internal ip address(which can be obtained by running ipconfig/all at command prompt).
this opens up all the ports of your system to external world.it’s very RISKY(NOT RECOMMENDED) though.when i tried this the moment i opened the ports thru dmz option i was infected with loads of spyware and adware.my desktop wallpaper changed automatically and seconds later my system went on restarting,so beware!!
testing on different types of modems very soon………..
i dont have virtual server option,what should i do?
please follow nsn155’s answer below.
alright people, this for those they do not have virtual server option , all u have to do is change your modem settings to bridge connection.
initially it will set as ppoemode.first save u r modem current settings at management>settings.backup.
after u have done tht now move to advanced setup>wan>
now u will see a table. click remove on every line,and then click remove on bottom of the page, and then save/reeboot.
next after u modem is reset, again go to advanced setup>wan>u will see a table ,click edit on the first row ie pppoee row
click next, click bridging ,next,next…. and then save /reboot.
now go to control panel>networkconnections> create a new connection
click next>connect to the internet>setup manually>connect using a broadband connection which uses a username and password> click next>next>and complete the process.
and now in ur network connections u will see a new connection.click on it and enter the details and u r good to go.
and now ports will be open.happy downloading at super high speedssssss.
it will work,so dont worry. if it does not change u r modem settings as they were previously orrrrrrrr call 23234770 which is tech office of bsnl. and ask them how to change u r connection to bridge mode.
June 17th, 2008 at 8:16 pm
thanks a lot!!
June 30th, 2008 at 3:00 am
nice work!!!
but the problem is that now instead of orange triangle there is a green one (thats good)
while on port forwarding test it still shows error that port isn’t been forwarded…
anything needs to be done here or all is working fine???
July 9th, 2008 at 4:08 am
hi tushar
first of all congrats !
if you find the green triangle then its fine,its portforwarded perfectly.if it shows it is not portforwarded on port forwarding test,try refreshing the page once or twice.you should be able to see correct result.
if not download the latest utorrent.(this should be of little help though)
if you notice any faster downloads or high speed downloads than before then dont bother about these tests at all.
happy downloading
August 6th, 2008 at 3:25 pm
this is a great job.thank u very very much.this works. i forward port for downloading files thru utorrent & bitcomet.utorreent works but bitcomet is not working.the connection indication is still gray in colour wat can i do?
August 7th, 2008 at 5:17 pm
thank u daya! i am glad u got it right.
as far as i know utorrent is the best torrent client.i havent tried others till now.
ill try others too and update here.keep checking
August 8th, 2008 at 1:39 pm
I am having the same complaint for my ut300r2u. but when i open 192.168.1.1 typed admin as user and passwaord . but i cant get the virtual server as u stated above ..kindly help me thru this issue plz
August 8th, 2008 at 2:56 pm
you are having old firmware.check out the article for old firmware in this site.
September 20th, 2008 at 5:09 pm
I have the same problem where I dont get the “Virtual Server” link. But when I click the “Old firmware” hyperlink in this page it brings the same page again!!!
Can you pls. fix it and if possible also mail me how to resolve the issue. Thanks
September 21st, 2008 at 12:29 pm
hey thanks a zillion…..u’ve been really gr8 help….
actually b4 goin thru ur site…i went thru another tutorial wher they said to enable the DMZ….they didint mention the harm it cud cause….i hav been infected by spyware b4…so i knw hw much of a pain it is…so thanks for saving me this time….
i had another minor query….
the thing is ….on my system….sites like
thepiratebay.org
torrentz
youtube etc
do not open…..can u help me out wit this….is it something to do wit my settings?????
November 6th, 2008 at 12:01 am
Suggest argue, because only in a dispute born truth.
November 15th, 2008 at 2:13 pm
hi,
when i try to connect to the router using 192.168.1.1 it asks me username and password.i did try using my log in data for bsnl but it did’nt work.
then i tried typing both admin ans password as admin but tht also did’nt work.
pls help me in connecting to the router by clearly wht admin and passwrd shld be used
November 15th, 2008 at 5:32 pm
you should not use your bsnl id and password to access router.
default is username=admin password=admin
try username =admin password =password
or else reset the modem and try the above step again.
if you are using usb to connect your modem then try accesing 192.168.1.2
you should be able to login easily
November 20th, 2008 at 12:44 pm
for me also d same problem. Virtual s not der plz help me:(
November 20th, 2008 at 12:51 pm
anjana! welcome to the oldfirmware department.check if you can fix it using the old firmware article .if you can’t fix it,we’ll come up with a solution shortly,bookmark this space.
November 20th, 2008 at 3:47 pm
alright people, this for those they do not have virtual server option , all u have to do is change your modem settings to bridge connection.
initially it will set as ppoemode.first save u r modem current settings at management>settings.backup.
after u have done tht now move to advanced setup>wan>
now u will see a table. click remove on every line,and then click remove on bottom of the page, and then save/reeboot.
next after u modem is reset, again go to advanced setup>wan>u will see a table ,click edit on the first row ie pppoee row
click next, click bridging ,next,next…. and then save /reboot.
now go to control panel>networkconnections> create a new connection
click next>connect to the internet>setup manually>connect using a broadband connection which uses a username and password> click next>next>and complete the process.
and now in ur network connections u will see a new connection.click on it and enter the details and u r good to go.
and now ports will be open.happy downloading at super high speedssssss.
it will work,so dont worry. if it does not change u r modem settings as they were previously orrrrrrrr call 23234770 which is tech office of bsnl. and ask them how to change u r connection to bridge mode.
November 20th, 2008 at 3:49 pm
in bridge mode u do not need a virtual server or static ip
November 21st, 2008 at 4:24 am
that was a really nice answer by nsn155.ill try to write a walkover as he told.did anyone get it right?
November 21st, 2008 at 5:28 am
Hi
Hello
This is a Very Good Website For Me
November 23rd, 2008 at 6:29 am
from chirag to admin (thru email)
Hey i GOT IT!!!!!!!! Thanks a lot admin…. It opened up almost all the ports.. Although the speed has not increased that much.. Used to d/l at around 25kbps, now its around 30… But its still an increase… I have to thank you for all the help.. And also that guy who posted the comment… Thanks a lot..
i thank nsn155 for posting da solution.
November 23rd, 2008 at 6:33 am
[...] the comments here first.if you dont find it working ,then reading down here may [...]
November 24th, 2008 at 11:30 am
Hi….
I am trying to forward my port for Counter Strike..but i am not able to access my modem UT300R2U by 192.168.1.1 or 192.168.1.2..plz help!!!
November 24th, 2008 at 5:30 pm
even me havin a same problem
i don have virtual server tab in my 192.168.1.1
November 24th, 2008 at 5:35 pm
@girish
if you dont have virtual server,check out nsn155 comment above.
@ kinshuk gupta
are you using any additional router.?
November 25th, 2008 at 12:34 pm
I am not using any other router…i am not able to understand the nsn155 comment..There is no response when i enter 192.168.1.1…….
November 25th, 2008 at 12:53 pm
Today,i don’t know how but I was able to access through 192.168.1.2……..
“FSP 2000 Version 6.2.1, AirportRd” was displayed and i asked the login and password..
but then admin-admin didn’t work…..
now what to do…I have tried all the combinations given above
November 25th, 2008 at 2:25 pm
thnx to nsn155.ur answer works like a charm man.nd also thnx to admin.if there is virtual srever option ,then also u can use nsn155 comment ie set in bridge mode.
now this is to both admin and nsn155 or others who have used the above method,i would like u to verify something for me
right now mine is a unlimited plan of 256kbps.so i get around 26—30 kbs.
i want to change my plan to home 500 which has a dl of around 250kbs.and is free at night.so when i have changed to this plan will i be able to get a speed around 250kbs.
when it is in bridge mode????????????????????
plz kindly reply.
November 25th, 2008 at 3:20 pm
i am using home 500 right now.i get around 190-230kbps.
the ideal value is 250kbps.
u may get around 190-230 kbps ,but that depends upon your locality,and the number of users there.
but one thing is for sure you will definitely get speed improvement if you change from unlimited to h500.
happy portforwarding!!
November 25th, 2008 at 4:33 pm
@kinshuk
are u not seeing modem page?
try admin and password as password.
November 26th, 2008 at 2:52 pm
this is not working for me.
should i go to the bsnl office?
November 26th, 2008 at 6:09 pm
1)try resetting the modem. at the back of ur modem the is a reset button.hold for around 15 secs or so, until ur modem resets . and then try admin @ admin as user name @ password.
orrrrrrrrrrrrrrrrrrrrrrrrrrrrr
2)
Access to your DSL router is controlled through three user accounts: admin, support, and user.
The user name “admin” has unrestricted access to change and view configuration of your DSL Router.
The user name “support” is used to allow an ISP technician to access your DSL Router for maintenance and to run diagnostics.
The user name “user” can access the DSL Router, view configuration settings and statistics, as well as, update the router’s software.
here both the user name and password has to be entered the same as above mentioned
at each respective field that u use. try using these .
November 27th, 2008 at 4:56 pm
Thanks a lot nsn155!!!!
Now,I want to forward my 27015 port for counter strike gaming…plz help in this too.
November 27th, 2008 at 7:53 pm
if u have virtual server tab then port forward the same way as shown clearly by
the admin.
now if u don’t have virtual server u can portforward using my comment above.
November 29th, 2008 at 4:43 pm
hello,i have tried everything but still it doesn’t work
after the first save n reboot i don’t get a table i.e after clicking remove button. so what do i do????
November 29th, 2008 at 4:52 pm
hey i tried nsn155’s comment
after clicking remove button there s no table after reboot
wat do i do????????
November 29th, 2008 at 8:45 pm
just click add in the same page ie advanced setup>wan>add>next>select bridging>next>next>—————->save/reboot.
and the rest of the process as mentioned in the previous comment,
and u r done.
December 3rd, 2008 at 5:39 pm
Hi,
I have subsribed BSNL Dataone broadband and they provided Dataone Broadband( Bsnl
UTSTARCOM
Modem model number: UT300R2U
I need to configure UPnP (Universal Plug and Play).. but this model doesn’t have I belive. How do I get the UPnP feature modem ? which modem type (1 or 2 or 3 or 4) from BSNL?
Regards,
Senthil
December 24th, 2008 at 8:17 pm
Great Article. Really helpful
December 27th, 2008 at 3:07 am
hey am havin ut 300r2u and when i tried 192.168.1.1 i don get the same page you ve displayd.. i get a differnt page and i don ve any virtual server over there… pls help me.. waiting for reply
December 27th, 2008 at 4:11 am
please read the comments before u comment.can u show us the page u get when u try 192.168.1.1
January 9th, 2009 at 6:24 am
sir, with due respect n regards, i’m using BSNL as connection and ut300r2u as modem.
it does not have this VIRTUAL SERVER option. what should i do. i get this ORANGE light n it says ip blocked. i’m using latest BITCOMET as torrent software. i need help. pls do reply.
awaiting reply.
gunch
January 9th, 2009 at 1:25 pm
@gunch
please follow nsn155 comment above.report here if it doesnt work for you
January 11th, 2009 at 6:36 am
admin, with regards, thanx for considering. i got few steps done by myself. i dont know how to post screen shots else i’ll do anything to post it. i wont be able to write what i did. i made it work, how much i dont know but i did
January 11th, 2009 at 6:39 am
i did it. thanx to nsn155. if anybody needs help on this may call me at
9872000201
9988000201
9915000201
thanx. i can give my time to my frenz who helped me. thanx.
January 12th, 2009 at 3:04 am
hello admin. regards. sir i worked out with nsn155’s method but i still have some problem. i’m getting green light on my bitcomet n i see my port open on http://www.canyouseeme.org but still i’m not getting the desired speed. its still the same as the old. its 31kbps max. what should i do??????
January 13th, 2009 at 7:18 am
Want 2 Sale Used BSNL UT300R2U Modem
I am interested in sale Used UT300R2U BSNL Modem in
Bangalore. The cost of a new modem is Rs
3500.Please contact with best price. 9731274498 Raju
January 14th, 2009 at 5:59 am
Hey guys i did wat u told…. mine is a UL750 plan and im getting only 30kbs max still after all the above mentioned steps ……..is there any other way to increase the speed or the only way is to change the plan to 500+…. ah…………….thankx…………..happy new year and happy pongal to all………..
January 14th, 2009 at 6:13 am
hey nsn ….
i did according to the procedure given by u in order to get the vitual server tab…but in my case even after doin to bridge the virtual tab is not to be seen…
other factor which i wanted to clarify is the network connections… i ve two network connections both are neccessary is it??? do reply
January 16th, 2009 at 12:40 pm
[...] Re: Port Forwarding @kalyan_1980 If the UT300R2U is new model in PF web site select Beetel 220BX. Modem setting pages are identical. http://i4.tinypic.com/5y2f8ds.jpg Open 192.168.1.1/main.html for Advanced Options. Give feedback. REFERENCE:PORTFORWARDING BSNL /DATAONE UT300R2U MODEM | techtricks.co.in [...]
January 16th, 2009 at 1:39 pm
@gunch
@ raviabi
try downloading 2 more files simulataneously after portforwarding.if the speed wont go beyond 30kbps then its normal ,portforwarding has nothing to do with it.the problem is with the broadband plan from isp.change ur plan to h500 or similar ones.
January 21st, 2009 at 8:58 pm
this is to everyone out there who r complaining about not getting speed.
1)if u r current plan is ul 750 u r max speed will only be about 30kbs.
2)if u r plan is home 500, combo, combo plus ….etc then u may get around 250kbs.
REMEMBER SPEED ALWAYS DEPENDS ON NO OF SEEDS U HAVE,AND WITH THEIR RESPECTIVE UPLOAD SPEED,WHICH WILL BECOME U R DOWNLOAD SPEED.
THIS IS IF U R USING TORRENTS. IF U DO NOT KNOW HOW TO USE TORRENTS,
U CAN ALWAYS DO DIRECT DOWNLOADING ie USING RAPIDSHARE,MEGADOWNLOAD …………ETC
January 29th, 2009 at 1:29 am
how do u know all this stuff…. even i need to learn them ..iam an electronics and communication engineer..
January 29th, 2009 at 8:07 am
this comes thru experience.
January 30th, 2009 at 5:12 am
i explored my settings and found that bridging mode is ideal for cscz server setup using hlds. i got linux ubuntu in which i can’t or i don’t know how to configure PPoEE id and pass..i wan’t to set my username and pass in my modem itself..modem model UT300RTU..now when i type 192.168.1.1 in address bar..we usually get a id and password field…but instead i get page cannot be displayed..i tried to reset my modem too..not working…help needed its very urgent…i gotta update my brand new Linux ubuntu..thank you in advance
January 30th, 2009 at 5:13 am
i think many had the same problem before..but the admin couldn’t understand it..or they didn’t describe it properly
January 30th, 2009 at 1:38 pm
@kesavan
what is cscz server and hlds?
if you are using ethernet to connect to modem and computer then 192.168.1.1 should open up the modem page on the browser.
if you are using usb to connect then i think you need to install the linux drivers supplied with the modem ,correct me if i am wrong.
try configuring the modem on a windows computer and then use on linux.it should work
i havent tried portforwarding on linux.
January 31st, 2009 at 3:43 pm
counter strike condition zero is cscz..hlds is half life dedicated server….i am using ethernet to connect to modem and computer…i am now using in windows only, but my modem is in bridging mode…i need to put it in ppoee before i can use it in linux…but when i try to open the modem settings using 192.168.1.1 it says page cannot be displayed..and my operating system is Windows Vista Home edition..its genuine..
February 3rd, 2009 at 8:19 pm
are you using any router along with bsnl modem?
did u try 192.168.1.2 ?
February 19th, 2009 at 7:53 pm
how to do port forwarding in bsnl usb connection……… I got a usb connection of BSNL… Please help
February 27th, 2009 at 5:10 pm
hi guys thnx nsn155 and admin for info
i configured the bridge connection still in torrent the test to check port forward is failing…plz help
February 27th, 2009 at 5:51 pm
also please tell me the method to load the saved back up file of bsnl dsl router configeration. thnx in advance…
March 7th, 2009 at 9:04 pm
Hi,
great article!!!
earlier i configured it through DMZ, but considering the risks (discussed here), i now am running in bridge mode. and speeds? toooooooooo fast. earlier i used to get only around 25-30 kbps but now its like 80-100 kpbs. so thanks a lot to admin n my dear nsn
But one problem: m unable to open 192.168.1.1. yes same problem, page unavailable. If i reset the modem from that button provided at the rear, would it restore to the default in pppoe mode? yes, i took backup while in pppoe mode. please help in this direction.
and one more thing: earlier in pppoe mode, the connection was all time on. But in bridge mode, do i need to connect each and every time i want to use net? What should i do if i want it like before (all time connected).
Thanks a lot for this great help
March 7th, 2009 at 9:21 pm
and also since i schedule all my downloads in nights, if i standby my pc in bridge mode, and then again power-on, the connection goes off, and i need to reconnect this manually, which is not going to work for me as earlier my pc used to do this automatically. please help…
March 11th, 2009 at 1:21 pm
It was an excellent reading.I added your rss to my rss reader!
March 12th, 2009 at 2:40 pm
no it won’t work if you restore the modem…i myself figured out the conflict..the problem is the dialer and the modem which is a networking device uses the same ip…you might notice some thing like unindentified connection or sort of.. if you have vista you can diagnose and renew the ip…then you can log on to 192.168.1.1
April 12th, 2009 at 12:15 am
Thanks alot for this great post !
Julie.
April 16th, 2009 at 3:42 am
after portforwarding its all kk ..thanx to nsn155…i also required y now and then connection fails ….due to bridge connection…..so after this i hav to reconnect …then only it connects and works ..but main pbm is it get connection abrupt cut ..so that it take time to regain its speed when it was downloading bfor…in utorrent only…wat i hav to do …some one comment plssssssssss
April 19th, 2009 at 5:26 am
all ok …but connection failure occurs regularly…if it is in bridge connection..anyone pls replyyyyyyyyyyyy soon pls …
April 24th, 2009 at 6:40 am
The problem of disconnection,may be arising due to the fact that the connection is being given parallely.
The is connection is being splitted before it gets to the wallport. The connection which we get from outside of the house is given to the wallport(the white box).
from there it is given it is given to the splitter from which one goes to the telephone and the other to ur modem.
please check the way ur connected and try to connect as above specified and see whether u encounter the above problem.
if u have not understood the above refer to QUICK START GUIDE which get along with the modem.
April 25th, 2009 at 3:51 am
really useful information. Thanks for helping me out!
May 7th, 2009 at 7:39 am
really a gr8 article, hats off to nsn and admin
May 15th, 2009 at 12:11 pm
Thanks a million admin!!! I found your article very helpful!! I’m also grateful to nsn155 for sharing his advice for those who don’t have a virtual server option… I found the steps he provided very helpful. Thanks again guys
May 22nd, 2009 at 1:33 pm
Thanks a lot!!!!. Since i got hooked to utorrent, i have tring to gather info on port forwarding. All said that static ip is required. Airetel provides this . But when i called up BSNL they said static ip is provided only for Rs 3000 and above plans.
Today one of my friends forwarded this link. When i saw the 1st half, i told him that i’ve seen this (this is a screen shot of probably an MTNL connection). But when i scrolled down, i had the required info.
You can’t imagine how happy i’m to have been able to configure the modem for top speed. Thanks
Thanks again
shibu
May 31st, 2009 at 12:02 pm
Great post man, very interesting,
I have bookmarked your blog to make it easier for me to keep up to date
with your posts in the future. Cheers
June 8th, 2009 at 12:59 pm
hi
i don hav virtual server option. how 2 change modem settings? not able 2 find mentioned options.
June 25th, 2009 at 12:29 pm
Dude, you ut300r2u router has the latest firmware. Anychance you can upload the firmware so that others can use it! Most of the people have the old version of the firmware. My e-mail is: itismee111@yahoo.co.in. Anyhelp would be appreciated. The firmware you are showing above is a new version, I have the old vesrion.
Thx
July 2nd, 2009 at 8:54 pm
hello,admin!!!
This is venkatesh. recently i have been facing kinda prob while torrenting.
the prob is tat ,at the bottom i can see a small triangle with yellow colour with an exclamation mark in it. it says there is a problem in n/w configuration.
i’m using UT-300R2U MODEM, and bsnl ul 750 home plan. plzzzzzzz help. i dont knw how to port forward.
July 7th, 2009 at 2:08 am
Very nice information. Thanks for this.
July 7th, 2009 at 4:40 am
We ve talk yon systems ahead! Well tried Windows 7! OMG…it is overwhelming! I not in the least thought I d guess this about windows but this one totaly blew me away! Analyse it whil its free! Healthier then VISTA!
July 8th, 2009 at 5:31 am
I m also xperiencing very low download speed………i m using BSNL 500C plan……
i m using WA3002G4 Modem will this steps work for my modem also………..?????
July 8th, 2009 at 11:04 am
Thanks for sharing.You wouldnt say how some websites are helpful source of informations like this one.Thanks
Jean
July 30th, 2009 at 1:34 am
[...] ======>>> For DMZ Para four : GUIDE: for comparison/study. ( old model ut300R2U) PORTFORWARDING BSNL /DATAONE UT300R2U MODEM | techtricks.co.in Para Five: REF: (1) No telnet configuring port forwarding & accessing advanced options in [...]
August 9th, 2009 at 2:19 am
i do all that but iam recieving a red color icon with an exclamation sign .wat to do for that?
August 21st, 2009 at 9:06 pm
Below mentioned are the details of Router/Modem:
Device Info
Board ID: 96338L-2M-8M
Software Version: 3.08.BSNL_02.01.02_tr64.
Bootloader (CFE) Version: 1.0.37-8.7
Firmware Version: UT300R2U.0011.01
Hardware Version: UT300R2U 2.2
Model Name: UT300R2U
WAN Info
VPI/VCI Con. ID Category Service Interface Protocol Igmp QoS State Status IP Address
0/35 1 UBR br_0_35 nas_0_35 Bridge N/A Disabled Enabled Up
Wide Area Network (WAN) Setup
Choose Add, Edit, or Remove to configure WAN interfaces.
Choose Save/Reboot to apply the changes and reboot the system.
VPI/VCI Con. ID Category Service Interface Protocol Igmp QoS State Remove Edit
0/35 1 UBR br_0_35 nas_0_35 Bridge N/A Disabled Enabled
MAC Filtering Setup
MAC Filtering Global Policy: FORWARDED
Please help me whether in the mentioned configuration i require port forwarding or not.
September 1st, 2009 at 3:43 am
@ NSN155…
I i dont have virtual server option & i followed whatever is said above.., but the new problem is everytime i connect to internet ,my computer HANGS. Kindly help me solve this problem
AWAITING REPLY
Regards,
Naveen
September 4th, 2009 at 12:01 pm
thanks guys, it works, when i connected in bridge mode, But what about the security matters, when all the ports are open.
November 20th, 2009 at 7:59 pm
Respected Sir….
can u tell me setting of port forwarding for BSNL ZTE ZXDSL 831II moderm???
i am wainting for reply sir……thanks
November 26th, 2009 at 11:56 am
I have bsnl ut300r2u , and I am on 512 kbps connection.
I tried the “i dont have virtual server option,what should i do?”.
After I deleted all rows and created a connection from network connections , I had no luck connecting to internet.
I gave up and put my computer in DMZ. The utorrent shows ports are open.
Any way what is the speed good download speed I can eexpect on my sort of connection. I see 50kpbs ?
December 5th, 2009 at 1:05 pm
hey i can only open one port thats 43537 i cannot get any other port to open